Drive specification ST8000VN004 Formatted (512 bytes/sector)# 8TB Guaranteed sectors (see Section 2.2) Heads 10 Discs 5 Bytes per logical sector 512 Bytes per physical sector 4096 Recording density. KBPI (Kb/in max) 2509 Track density. KTPI (ktracks/in. 0 skew) 371 Areal density. (Gb/in2. @ 0 skew mid-disk) 930 Spindle speed (RPM) 7200 Internal data transfer rate (Mb/s max) 2850 Sustained data transfer rate OD (MiB/s max) 200 (210 MB/s max) I/O data-transfer rate (MB/s max) 600 ATA data-transfer modes supported PIO modes 0–4 Multiword DMA modes 0–2 Ultra DMA modes 0–6 Cache buffer 256MB (262.144KB) Weight: (maximum) 716g (1.579 lb) Average latency 4.16ms Power-on to ready (sec) (typ/max) 23/30 Standby to ready (sec) (typ/max) 23/30 Startup current (typical) 12V (peak) 1.8A Voltage tolerance (including noise) 5V +10/-5% 12V ±10% Non-Operating temperature –40° to 70°C (Ambient Temperature. see sections 2.6.1 and 2.11) Operating temperature* 5°C Operating temperature* 70°C Temperature gradient (°C per hour max) 20°C (operating) 30°C (nonoperating) Relative humidity* 5% to 95% (operating) 5% to 95% (nonoperating) Relative humidity gradient 30% per hour max Altitude. operating –304.8 m to 3.048 m (–1000 ft to 10.000+ ft) Seagate IronWolf SATA Product Manual. Rev. B 7 # One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. * See Section 2.11. Reliability for rated MTBF device operating condition requirements. Altitude. nonoperating (below mean sea level. max) –304.8 m to 12.192 m (–1000 ft to 40.000+ ft) Operational Shock (max at 2 ms - typical) Read 70 Gs / Write 40 Gs Non-Operational Shock (max at 2 ms - typical) 300 Gs Vibration. operating 5–22 Hz: 0.25 Gs. Limited displacement 22–350 Hz: 0.50 Gs 350–500 Hz: 0.25 Gs Operation Rotational vibration 20–1500Hz: 12.5 rads/s² Vibration. nonoperating 10–500 Hz: 5.0 Grms ref Drive acoustics. sound power (bels) Idle 2.8 (typical) 3.0 (max) During periods of drive idle. some offline activity may occur according to the SMART specification. which may increase acoustic and power to operational levels. Performance seek 3.2 (typical) 3.4 (max) Nonrecoverable read errors 1 sector per 1015 bits read Annualized Failure Rate (AFR)* 0.87% based on 8760 POH Maximum Rated Workload* Maximum rate of <180TB/year Workloads exceeding the annualized rate may degrade the drive MTBF and impact product reliability. The Annualized Workload Rate is in units of TB per year. or TB per 8760 power on hours. Workload Rate = TB transferred * (8760 / recorded power on hours). Warranty To determine the warranty for a specific drive. use a web browser to access the following web page: http://www.seagate.com/support/warranty-and-replacements/. From this page. click on the “Is my Drive under Warranty” link. The following are required to be provided: the drive serial number. model number (or part number) and country of purchase.The system will display the warranty information for the drive. Load-unload cycles (command controlled) 600.000 Supports Hotplug operation per Serial ATA Revision 3.3 specification Yes https://www.seagate.com/es/es/internal-hard-drives/hdd/ironwolf/#specs